“AS 5101.3.2-2008” has been added to your cart. View cart
🔍
Purchase the full subscription package now and enjoy a 40% discount, along with free updates for future editions.
AS 1154.3-2009
$125.14
Insulator and conductor fittings for overhead power lines, Part 3: Performance and general requirements for helical fittings
Specifies performance and general requirements for helical fittings for use on overhead electrical power lines.
Table of contents
Header
About this publication
Preface
1 Scope and general
1.1 Scope
1.2 Referenced and related documents
1.2.1 Referenced documents
1.2.2 Related documents
1.3 Definitions
1.4 General requirements
1.4.1 Defects
1.4.2 Design
1.4.3 Materials
1.4.4 Surface finish
1.4.5 Protection against corrosion
1.5 General requirements for tests
1.5.1 Type tests
1.5.2 Batch tests
1.5.2.1 Sampling
1.5.2.2 Acceptance
1.6 Verification of dimensions
1.7 Colour codes for helical fittings
1.7.1 Colour codes for conductors
1.7.2 Colour codes for insulator neck diameters
2 Anchor and tension fittings
2.1 Items to be specified by the purchaser or declared by the manufacturer
2.1.1 Conductors
2.1.2 Optical ground wire (OPGW)
2.1.3 All dielectric self-supporting (ADSS) cable
2.2 Type test for glue
2.2.1 General
2.2.2 Test assembly and procedure
2.3 Mechanical strength type tests
2.3.1 Anchor fittings other than fittings for ADSS and OPGW cables
2.3.1.1 Test assembly and procedure
2.3.1.2 Requirement
2.3.2 Anchor fittings for ADSS cables
2.3.3 Tension fittings
2.3.3.1 Test assembly and procedure
2.3.3.2 Requirement
2.3.4 Anchor fittings for OPGW cables
2.3.4.1 Test assembly and procedure
2.3.4.2 Requirements
2.4 Electrical type tests
2.4.1 Resistance test (excluding OPGW)
2.4.1.1 General
2.4.1.2 Test assembly and procedure
2.4.1.3 Requirement
2.4.2 Heating cycle test
2.4.2.1 General
2.4.2.2 Test current
2.4.2.3 Test assembly and procedure
2.4.2.4 Requirement
2.4.3 Short-time current test
2.4.3.1 General
2.4.3.2 Test current
2.4.3.3 Test assembly and procedure
2.4.3.4 Requirement
2.5 Batch tests
2.5.1 Verification of dimensions
2.5.2 Mechanical and electrical tests
2.5.3 Galvanizing tests
3 Suspension and support fittings
3.1 Specification details—Items to be specified by the purchaser or declared by the manufacturer
3.1.1 Conductors
3.1.2 Optical ground wire (OPGW)
3.1.3 All dielectric self-supporting (ADSS) cable
3.2 Mechanical strength type tests
3.2.1 Holding tension (withstand slip) test
3.2.1.1 General
3.2.1.2 Test assembly and procedure
3.2.1.3 Requirement
3.2.2 Failing load test
3.2.2.1 Suspension fittings
3.2.2.2 Support fittings
3.3 Mechanical strength and optical type tests for fittings for OPGW cables
3.3.1 General
3.3.2 Suspension fittings
3.3.2.1 Optical performance at maximum deviation
3.3.2.2 Optical performance and withstand slip
3.3.2.3 Requirement
3.4 Electrical type test—Short-time current test
3.4.1 General
3.4.2 Test current
3.4.3 Test assembly and procedure
3.4.4 Requirement
3.5 Batch tests
3.5.1 Verification of dimensions
3.5.2 Mechanical tests
3.5.3 Galvanizing tests
4 Repair and protective fittings
4.1 Items to be specified by the purchaser or declared by the manufacturer
4.1.1 Conductors
4.1.2 Optical ground wire (OPGW)
4.1.3 All dielectric self-supporting (ADSS) cable
4.2 Repair fittings
4.2.1 General requirements
4.2.2 Preparation of conductor for the type test
4.2.3 Mechanical strength type test
4.2.3.1 Test assembly and procedure
4.2.3.2 Requirement
4.3 Protective fittings
4.3.1 Armour rods and line guards
4.3.2 Spiral vibration dampers
4.4 Batch tests
4.4.1 Verification of dimensions
4.4.2 Galvanizing tests
Cited references in this standard
Please select a variation to view its description.
| Published | 12/02/2009 |
|---|---|
| Pages | 21 |
Please select a variation to view its pdf.
