AS ISO/IEC 18745.2:2023 identically adopts ISO/IEC 18745 2:2021, which defines the conformance test plan, based on ISO/IEC 10373 6, for the contactless interface of eMRTDs and eMRTD associated readers compliant with ICAO Doc 9303.
Table of contents
Header
About this publication
Preface
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Test methods for eMRTD
5.1 General test conditions
5.1.1 General
5.1.2 Test environment
5.1.3 Test conditions for PICC
5.1.4 Applicant information
5.1.5 Test report
5.2 Test of ISO/IEC 14443-1 parameters
5.2.1 Antenna size and PICC Class 1 verification (optional)
5.2.1.1 Purpose
5.2.1.2 Test procedure
5.2.1.3 Test report
5.2.2 Static electricity
5.2.2.1 Purpose
5.2.2.2 Test procedure
5.2.2.3 Test report
5.2.3 Alternating magnetic field
5.2.3.1 Purpose
5.2.3.2 Test procedure
5.2.3.3 Test report
5.3 Test of ISO/IEC 14443-2 parameters
5.3.1 eMRTD transmission
5.3.1.1 Purpose
5.3.1.2 Test procedure
5.3.1.3 Test report
5.3.2 Operating field strength
5.3.2.1 Purpose
5.3.2.2 Test procedure
5.3.2.3 Test report
5.3.3 eMRTD reception
5.3.3.1 Purpose
5.3.3.2 Test procedure
5.3.3.3 Test report
5.3.4 eMRTD maximum loading effect
5.3.4.1 Purpose
5.3.4.2 Test procedure
5.3.4.3 Test report
5.3.5 eMRTD resonance frequency (optional)
5.3.5.1 Purpose
5.3.5.2 Test procedure
5.3.5.3 Test report
5.3.6 eMRTD EMD level and low EMD time test (optional)
5.3.6.1 Purpose
5.3.6.2 Test procedure
5.3.6.3 Test report
5.4 Test of ISO/IEC 14443-3 and ISO/IEC 14443-4 parameters
5.5 List of the test command sequences
5.5.1 General
5.5.2 Test commands for eMRTD supporting only BAC
5.5.2.1 TEST_COMMAND_SEQUENCE1
5.5.2.2 TEST_COMMAND1
5.5.2.2.1 TEST_COMMAND1(1)
5.5.2.2.2 TEST_COMMAND1(2)
5.5.2.2.3 TEST_COMMAND1(3)
5.5.2.3 TEST_COMMAND2
5.5.2.3.1 TEST_COMMAND2(2)
5.5.2.3.2 TEST_COMMAND2(3)
5.5.2.4 TEST_COMMAND3
5.5.3 Test commands for eMRTD supporting PACE
5.5.3.1 General
5.5.3.2 TEST_COMMAND_SEQUENCE1
5.5.3.3 TEST_COMMAND1
5.5.3.3.1 TEST_COMMAND1(1)
5.5.3.3.2 TEST_COMMAND1(2)
5.5.3.3.3 TEST_COMMAND1(3)
5.5.3.4 TEST_COMMAND2
5.5.3.4.1 TEST_COMMAND2(2)
5.5.3.4.2 TEST_COMMAND2(3)
5.5.3.5 TEST_COMMAND3
5.6 Functionality check test
5.6.1 General
5.6.2 Optional procedure 1: Application functionality check test
5.6.2.1 Purpose
5.6.2.2 Test setup
5.6.2.3 Test procedure
5.6.2.4 Test report
5.6.3 Optional procedure 2: Electrical functionality check test
5.6.3.1 Purpose
5.6.3.2 Test setup
5.6.3.3 Test procedure
5.6.3.4 Test report
6 Test methods for eMRTD reader
6.1 General test conditions
6.1.1 General
6.1.2 Test environment
6.1.3 Test conditions for PCD
6.1.4 Applicant information
6.1.5 Test report
6.1.6 Definition of test positions
6.1.6.1 General
6.1.6.2 Volume definition
6.1.6.3 Volume location
6.1.6.4 Test positions
6.2 Test of ISO/IEC 14443-1 parameters
6.2.1 Alternating magnetic field
6.2.1.1 Purpose
6.2.1.2 Test procedure
6.2.1.3 Test report
6.3 Test of ISO/IEC 14443-2 parameters
6.3.1 Carrier frequency
6.3.1.1 Purpose
6.3.1.2 Test procedure
6.3.1.3 Test report
6.3.2 eMRTD reader field strength
6.3.2.1 Purpose
6.3.2.2 Test procedure
6.3.2.3 Test report
6.3.3 Modulation index and waveform
6.3.3.1 Purpose
6.3.3.2 Test procedure
6.3.3.3 Test report
6.3.4 Load modulation reception
6.3.4.1 Purpose
6.3.4.2 Test procedure
6.3.4.3 Test report
6.3.5 eMRTD reader EMD immunity test (optional)
6.3.5.1 Purpose
6.3.5.2 Test procedure
6.3.5.3 Test report
6.3.6 eMRTD reader EMD recovery test (optional)
6.3.6.1 Purpose
6.3.6.2 Test procedure
6.3.6.3 Test report
6.4 Test of ISO/IEC 14443-3 and ISO/IEC 14443-4 parameters
6.5 List of test command sequences
6.5.1 General
6.5.2 Test commands
6.5.2.1 UT_TEST_COMMAND1
6.5.2.2 UT_TEST_COMMAND2
6.5.3 Default test command sequence
6.5.4 Test_command_sequence_1
6.5.5 Test_command_sequence_2
6.6 Measurement positions
7 Specific access control test sequences
7.1 General
7.2 List of the test command sequences with EAC for eMRTD
7.2.1 General
7.2.2 Test commands for eMRTD supporting EAC
7.2.2.1 TEST_COMMAND_SEQUENCE1
7.2.2.2 TEST_COMMAND1
7.2.2.3 TEST_COMMAND2
7.2.2.4 TEST_COMMAND3
7.2.3 Test commands for eMRTD supporting PACE and EAC
